DESCRIPTION

Easy line marking for car parks, roads and entrance ways

Resincoat Car Park Line Marking Paint saves you both time and money whilst creating a high visibility line that will brighten up your car park or other space that requires zone demarcation. The paint is heavy-duty enough to survive through harsh weather and under heavy, regular vehicle traffic. This paint is great for creating white or yellow lines on tarmac surfaces but is also available in a wide range of other colours to suit any type of job.

 

COVERAGE RATES

Please see below for coverage rates. If you are coating a large area and would like expert advice, please call our team who will be happy to assist you.

1kg: 50 linear metres at a width of 10cm

2.5kg: 150 linear metres at a width of 10cm

Please note: the above coverage rates are per coat, in most cases we advise 2 coats.

 

APPLICATION GUIDE

Preparation

We would recommend removing traces of existing lines before applying this paint, especially if it is flaky, as this will negatively impact adhesion of the paint to the surface. Any cracks, damage or defects in the concrete should be made good using repair compounds. Once dried, it will be necessary to clean and then lightly abrade the existing lines and apply Resincoat Car Park Line Marking Paint directly over the top. Ensure that the concrete is clean and free from dust, laitance, oil etc. A wire brush is generally sufficient to lift and clear debris. The loose debris and material must be vacuumed away after brushing or sanding. 

 

Application

We advise when applying our products that the ambient temperature is at least 7°C, though this product can cure as low as 0°C.

1. Apply masking tape to mark off the area you would like to cover

2. Mix Part A on its own with a mixing paddle attached to an electric drill for about 2 minutes before adding ALL of Part B and continue to mix for another 90 seconds, keeping the paddle in suspension to avoid mixing air into the unit.

3. Pour entirety of the tin's contents into a plastic paint scuttle or tray.

4. Immediately begin applying your paint with a nylon-bonded resin suitable roller.

5. As soon as the first coat has started curing (is no longer tacky to touch) you can re-coat; this should take 1-2 hours. Please note: as this product dries quickly, it is recommended that you remove the masking tape before it completely cures.

6. The cured final coat is ok for foot traffic. Cars and heavy objects, however, should be left off the new coating for the first 16 hours and chemicals including water should not be introduced for the first 2 days (full chemical cure).

 

PLEASE NOTE: The pot life of this product is 20 minutes. This means that once parts have been mixed, the paint will start to chemically cure after this time. Ensure you remove the paint from the tin in this window. The paint will then be workable on your floor for up to 30 minutes. 

Pot life = Time to harden in pot following addition of hardener

Working Time = Time to apply product before it becomes unworkable

 

USEFUL INFORMATION

Roller sleeves should be used once per coat, two coats will require two roller sleeves.

This product should NOT be split. Taking smaller quantities from each tin, even if measured correctly, may cause issues with activating.

This product is NOT self levelling.

LMP053

Data sheet

Appearance
Smooth, High Visibility Lines
Composition
Polyaspartic Line Marking Paint
Substrates
Concrete, Tarmac And Asphalt
Product Components
Resin (Part A) + Activator (Part B)
Typical Installations
Car Park Line Marking, Walkways, Zone Marking, Road Markings, Disabled Parking Bays, Etc
Re-coat/Foot-traffic Time (at 20°C)
60 Minutes
Drying Time (at 20°C)
24 Hours
Pot Life
The Pot Life Of This Product Is 20 Minutes
Application Tools
Roller, Epoxy Sleeve

Specific References

ean13
5056489451005
upc
500778050578

Download

Colour Chart

Download (129.88KB)

Frequently Bought Together

3 other products in the same category:

Comments (3)
Reviews